Skip to content

uPVC vs aluminium windows in Pakistan: what to pay

By Sakunat7 November 2026 6 min readAI-assisted
Newly installed uPVC windows on a double-storey house in Rawalpindi

A contractor quotes you PKR 650 per square foot for aluminium windows on a 10 marla house in Bahria Town Rawalpindi. A second one quotes PKR 1,100 for uPVC. A carpenter says wood is "only a little more." Nobody explains what you are actually paying for, and a ten marla double-storey house easily has 25 to 35 windows and doors, so the choice moves your budget by hundreds of thousands of rupees. That is the real question behind uPVC vs aluminium windows: what is inside the price. These rates are illustrative of what quotes often look like; they shift with aluminium and PVC prices, so get fresh quotes before you decide.

What windows actually have to do in Pakistan

In most of our cities the job is not insulation alone. In Lahore, Multan and Karachi, windows must keep out summer heat and dust. In Islamabad, Murree and the northern areas they must also hold in winter warmth. During Punjab's smog season, a poorly sealed window lets fine particles straight in. So judge a window on four things: frame material, glass, the seal and the hardware. Price differences usually sit in the last three, not the frame name on the quotation.

Aluminium: the common choice, with a catch

Bricklayer building a wall on a housing site
Bricklayer building a wall on a housing site

Aluminium sections are strong, thin and easy to find. A reasonable local range for a standard sliding window is PKR 600 to PKR 1,000 per square foot, depending on section thickness, powder coating and glass. The catch is that aluminium conducts heat. In a south or west facing room, the frame itself gets hot in summer and cold in winter. Thin sections also flex, so sliding panels can jam within a few years.

Ask which section thickness is quoted and who makes it. A contractor who says "aluminium" without a thickness may be pricing the lightest profile. Request it written on the quotation.

uPVC: better sealing, higher price

uPVC frames do not conduct heat the way aluminium does, and the multi-chamber profiles with rubber gaskets seal well against dust and draughts. Typical quotes run roughly PKR 1,000 to PKR 1,800 per square foot, widely varying with profile quality and whether steel reinforcement is used inside. Good uPVC has internal steel in larger frames; cheap versions skip it and sag.

uPVC suits bedrooms and anywhere noise, dust or cold matters. It is less suited to very large openings unless reinforced, and poor quality sections can yellow under strong sun. Ask for a sample corner and check how thick the wall of the profile is.

Wood: durable if the timber is right

Seasoned deodar or sheesham windows look good and insulate well, but the price depends almost entirely on timber quality and workmanship. Cheap wood warps in humid months or after a monsoon, and unseasoned timber is the common failure. If you go this route, inspect the timber before it is cut and insist on a proper finish. Cost per square foot varies too widely to quote a trustworthy single range, so compare two or three carpenters on the same drawing.

Glass matters as much as the frame

A single 5 mm clear pane is the budget default. Options to ask about:

  • Double glazing (two panes with an air gap): the biggest improvement for heat, cold and noise, and a price jump that can be substantial per window. Worth it in west-facing bedrooms and on main roads.
  • Tinted or reflective glass: cuts glare and some heat for less money than double glazing.
  • Laminated glass: better for security and noise, often considered for ground-floor and road-facing windows.

Spending extra only on the two or three worst-facing windows often gives most of the benefit. You can use the construction cost calculator to see how finishing choices fit the overall build budget.

The seal and hardware decide how it ages

Window seals fail first. Ask for EPDM or similar rubber gaskets, not foam strips, and check that sliding rollers are stainless or well-coated. Hardware such as handles, locks and hinges is where quotations hide savings. A window with good glass but a weak lock or a rattling track will disappoint in two years.

Installation counts equally. Frames should be fixed to the wall opening with proper fasteners and sealed around with weatherproof sealant. A gap left around the frame leaks dust and rain no matter what material you chose.

Timing: after plaster, before paint

Windows are usually fixed once the plaster is done and before the final paint. Order them early, because made-to-measure frames take weeks. Measure the finished openings, not the drawing, because block work is rarely exact. Plumbing and electrical checks come before plaster, as covered in this checklist. If your quotes arrive in different formats, the BOQ method for comparing contractor quotes keeps the comparison fair.

Three illustrative budgets for a 10 marla house

Take 30 windows and doors averaging 12 square feet of glazed area, roughly 360 square feet in all. These are planning examples built from the ranges above, not quotes.

  • Economy: standard aluminium sections with single clear glass at about PKR 600 to PKR 800 per square foot, around PKR 216,000 to PKR 288,000 in total.
  • Balanced: heavier aluminium or reinforced uPVC for the main rooms and economy sections elsewhere, perhaps PKR 350,000 to PKR 500,000 overall.
  • Comfort-first: reinforced uPVC throughout with double glazing in the exposed rooms, which can run well beyond PKR 650,000 depending on glass and hardware.

The balanced option usually gives the best value because it spends where the sun, noise and dust are worst. Before you finalise, price each version on the same schedule.

Mistakes I see repeatedly

Measuring from drawings instead of the finished openings is the first. The second is accepting "same as sample" without a written specification, then receiving thinner sections on delivery. The third is forgetting mosquito mesh, grills and curtain-rod allowances until after the windows are installed, so that fittings clash. A fourth is ignoring ventilation: a fully sealed room with no openable section, in a kitchen or a bathroom, invites damp and mould.

Also think about cleaning. Tall fixed panes on an upper floor are difficult to reach. Ask for tilt or reversible sashes where you can, particularly in a dusty city like Lahore or Faisalabad where the glass needs washing often.

A quick way to compare quotes

Ask each supplier to quote the same schedule: window number, width, height, opening type, frame material and section thickness, glass type, hardware, and installation. Convert every line to a price per square foot. Then total each version. Suppliers who refuse a line-by-line quote are telling you something.

Also ask for:

  1. A sample or a finished project you can visit.
  2. A written warranty period on frames, seals and hardware.
  3. Delivery time and what happens if measurements are wrong.

Your next step

Before the first payment, mark every opening on the drawing as sun-facing, road-facing or sheltered. Choose better glass and uPVC or heavy aluminium for the first two groups, and economical sections for the rest. Get at least three written quotes on the same schedule, and visit one installed job. If you are still deciding whether to build or buy, compare with ready homes under properties for sale. A short afternoon of measuring and comparing can save you from replacing windows within five years.

#windows#uPVC#aluminium#finishing#construction cost

Frequently asked questions

Is uPVC better than aluminium for windows in Pakistan?

uPVC seals better against dust, draughts and noise and does not conduct heat like aluminium, so it suits bedrooms and exposed rooms. It usually costs more per square foot. Good aluminium with thick sections works well elsewhere. Quality of profile, gaskets and reinforcement matters more than the material name.

Is double glazing worth it in Pakistan?

It is most worthwhile on west-facing bedrooms, busy roads and in cold areas like Islamabad or the north, where it cuts heat, cold and noise. Because it adds noticeably to the price, many owners fit it only in the two or three worst-affected rooms and use single glass elsewhere.

When should windows be fixed during construction?

Usually after plaster and before final paint. Order early because made-to-measure frames take weeks, and measure the finished openings rather than the drawing, since block work is rarely exact. Fixing and sealing around the frame properly is as important as the frame itself.