Underground water tank size and placement for a Pakistani house
The grey structure of a 10 marla house is up and the mason asks where the underground tank goes. If you answer "somewhere near the gate," you have just locked in a decision that is expensive to undo. Pipes and tanks sit inside walls and under floors. Once tiles are down, a wrong plumbing layout means breaking work you already paid for. This guide covers the choices that matter, in the order you will face them.
Underground water tank size: start with the water you need
Planning figures vary, so treat these as a starting point and ask your engineer or architect to confirm them. Households in Pakistani cities often use somewhere around 150 to 200 litres per person per day for all purposes, with more in summer and in homes with gardens, washing machines and a car wash habit. For a family of eight, that is roughly 1,200 to 1,600 litres a day.
Where supply is irregular, as it is in many parts of Karachi, Lahore and Rawalpindi, plan for two to three days of storage. That puts the target at about 3,000 to 5,000 litres for the household as a whole, split between an underground tank and an overhead tank. If your area has a reliable municipal or society supply every day, you can go smaller. If you rely on a tanker or a bore that runs on a schedule, plan larger.
A simple volume check helps you decide the tank size. One cubic foot holds roughly 28 litres. An underground tank with inside dimensions of 8 ft by 6 ft by 5 ft deep holds 240 cubic feet, or about 6,800 litres. That is comfortable for most 10 marla homes with a booster pump, and it is a reasonable size to ask for at the design stage. If you are building a rental portion upstairs, add to this for each additional household.
Where the underground tank should go
The tank decides the rest of the layout, so place it early.
- Near the water source and the pump. The supply line, bore or society connection should reach the tank without a long run.
- Away from the septic tank or soakage pit. Keep a good distance between them and put the water tank uphill, if the plot has any fall. Ask your engineer for the minimum separation that applies to your soil and local rules.
- Accessible for cleaning. A manhole of at least 2 by 2 ft, with a proper lid, lets a person get in to scrub the tank once or twice a year. Do not bury it under the porch tiles.
- Outside the load path of vehicles, or built with a slab designed for that load. A tank under the car porch needs a stronger roof slab and a stronger lid.
Waterproofing inside the tank is not optional. Ask the contractor what product will be used and how many coats, and request that the tank be filled and checked for leaks for at least a few days before backfilling or plastering. A leaking underground tank wastes water for years without anyone noticing.
Overhead tank, booster pump and pressure
Most houses use a pump to lift water from the underground tank to an overhead tank on the roof. Gravity then feeds the taps. Two details cause the most complaints later.
- Height of the overhead tank above your highest fixture. A tank only a foot or two above the top-floor shower gives weak pressure. Place the stand to give a few feet of head, and plan the roof space so that the tank is not in the way of a future solar array. If you are planning solar panels, settle the roof layout first so the two do not compete for the same corner.
- Pump size and wiring. Ask your electrician to run a dedicated line to the pump with its own breaker, and to include a float switch or automatic cut-off. Dry running destroys pumps and flooded roofs ruin ceilings.
If you want more even pressure on every floor, a small pressure-booster setup can serve instead of, or alongside, an overhead tank. It costs more and uses electricity whenever you open a tap, so it suits houses where power is steady or a backup is in place.
Pipe materials: what goes in the wall
Plumbing rework is costly, so the choice of pipe matters more than the price difference between brands.
- PPR pipes with welded joints are widely used for both cold and hot water inside walls. The welded joints are reliable when done by a trained plumber, and the pipes do not corrode.
- CPVC is another option, often used for hot and cold lines, though pricing and availability vary by city.
- uPVC is common for drainage and rainwater lines, not for hot supply.
- GI (galvanised) pipes are older practice and tend to rust; they are rarely the best choice for new work.
Ask for pressure testing before plastering. The plumber should close the lines, pressurise them and leave the gauge in place for a period you agree in advance, often an hour or more, while you watch. This is one of the most valuable checks you can ask for, and it costs almost nothing.
Keep hot and cold lines separate and labelled, and insulate hot lines that run through cold walls or outdoors, particularly in northern cities like Peshawar, Murree and Islamabad where winters are sharp. A winter heater or geyser line that freezes or loses heat is a common headache.
Bathrooms, kitchens and drains
Drains rely on slope, not pumps, so they need attention at the grey-structure stage.
- Slope: a floor drain or waste pipe should fall at a steady gradient toward the outlet. Ask the mason to confirm the slope before the floor screed is cast.
- Pipe sizes: a 4 inch pipe is the common size for toilet soil lines, with smaller sizes for basins and kitchen sinks. Confirm with your engineer.
- Inspection chambers: place one at every change of direction and at the point where lines join the main sewer or septic tank. Without them, a blockage means breaking the floor.
- Vents: soil pipes need a vent to the roof so that traps do not siphon dry and let smell back in.
- Kitchen waste: use a grease trap or a basic trap and keep oil out of the main line.
For bathrooms, mark the geyser position, shower mixer height and washing machine point on the wall drawings before the plumber starts, and take photographs of every wall before plaster covers the pipes. Those photographs will save you a day of guessing years from now, when you drill a hole to hang a mirror.
Cost: where the money goes
Plumbing cost for a 10 marla house depends on the number of bathrooms, the pipe material, the brand of fittings and the labour rates in your city, and these have all moved with materials prices in recent years. As a planning approach rather than a quote:
- List every point: taps, showers, toilets, basins, kitchen sinks, washing machine, outdoor taps, geyser lines.
- Ask two or three plumbers for a per-point labour rate and an itemised material list, separately.
- Add the underground tank, the overhead tank and stand, the pump and the cut-off controls.
- Allow a contingency for changes, since plans always move on site.
Use the construction cost calculator for the overall budget, then check how plumbing and sanitary fittings sit in the estimate. Fittings, the part you see, can swing the bill widely between an economy and a premium finish.
Mistakes contractors make on site
You can prevent most of them by simply being there on the key days.
- Tank walls laid in thin or poorly cured brickwork with weak waterproofing. Ask for reinforced concrete or well-built, properly plastered walls.
- Pipes buried without testing, followed by a leak discovered after tiling.
- No slope check before the floor screed, leaving water pooling in bathrooms.
- No isolation valves, so one broken tap means shutting down the whole house. Ask for a valve at each bathroom and the kitchen.
- Pump wired to a general socket rather than its own line.
What to do before the plaster goes on
This week, ask your contractor for a one-page plumbing drawing: tank positions, pipe runs, valve locations and drain slopes. Walk the site with it, tick each item and photograph the open walls. Insist on a pressure test before plaster, and keep the photographs in a folder with your other house documents. If you are still deciding on the build budget and the stages, the construction cost calculator and a local engineer on the site will do more for you than any guess. An hour spent on the plumbing plan now spares you weeks of broken tiles later.
Frequently asked questions
What size underground water tank does a 10 marla house need?
A common planning figure is 150 to 200 litres per person per day, with two to three days of storage where supply is irregular. For a family of eight that suggests roughly 3,000 to 5,000 litres across tanks. An 8 by 6 by 5 ft underground tank holds about 6,800 litres. Confirm sizing with your engineer.
Which pipe is best for hot and cold water inside walls?
PPR with welded joints is widely used for cold and hot supply because it does not corrode, and CPVC is another option. uPVC suits drainage, not hot water. Whatever you choose, insist on a pressure test before plastering and keep photographs of the pipe runs for future drilling.
Why test plumbing before plaster in a new house?
Pipes buried in walls and floors are costly to reach later. A pressure test, where the lines are pressurised and a gauge is watched for a set time, reveals leaking joints while the wall is still open. Fixing one joint then costs little compared with breaking finished tiles.
Keep reading
Underground water tank size Pakistan: a 10 marla plan
Count people, not marlas. A simple litres-per-day method, a worked 10 marla example, and the checks to demand before the slab is cast.
27 Oct 2026 6 min read
Plumbing and electrical checks before plaster in Pakistan
Once plaster goes on, pipes and wires are hidden for decades. Test, photograph and sign off every concealed line first.
26 Oct 2026 6 min read
Electrical wiring plan for a 10 marla house in Pakistan
Decide loads, circuits and point locations on paper before plastering. A few spare conduits and a circuit schedule save expensive wall repairs.
18 Nov 2026 6 min read
