Skip to content

Check saria on delivery in Pakistan: weigh, measure, reject

By Sakunat6 November 2026 6 min readAI-assisted
Steel reinforcement bars stacked on a Pakistani construction site being measured with a tape

A truck backs onto your plot in Gujranwala or Bahria Town Rawalpindi, the driver says "two ton, #4 saria," and the bill is already written. Most owners nod, sign, and let the mistri start tying. That five-minute window, before the bars leave the trolley, is the cheapest place in the whole build to catch a problem. Here is how to check saria on delivery with a tape, a calculator and a weighing slip.

Know what you ordered in kilograms per bar

Pakistani sites mostly use imperial bar numbers: #3, #4, #5, #6. The number is the diameter in eighths of an inch, so #4 is half an inch. That gives a handy rule: weight per metre is roughly the bar number squared, divided by 16.

  • #3 (3/8 inch): about 0.56 kg per metre
  • #4 (1/2 inch): about 1.0 kg per metre
  • #5 (5/8 inch): about 1.56 kg per metre
  • #6 (3/4 inch): about 2.24 kg per metre

Bars usually arrive in 40-foot lengths, which is about 12.19 metres. So one full #4 bar should weigh close to 12 kg, a #3 about 6.8 kg, a #5 about 19 kg and a #6 about 27 kg. Write these on the back of your hand or in your phone before the truck arrives. They are the numbers every other check depends on.

I've watched a "#4" delivery where the bars felt oddly light to the labourers carrying them. Weighed against the table above, the bundle was nearly a full size under. The supplier called it "market standard." It was not.

Weigh a sample, not just the truck

Solar panels installed on a residential rooftop
Solar panels installed on a residential rooftop

Ask for the weighbridge slip (kanta parchi) from the supplier's side and compare it with a second weighing if there is a bridge near your site. Trucks differ by a few percent between bridges, so do not panic over a small gap. A large gap is worth a phone call before unloading.

Then check the bars themselves, because total weight can be right while the bars are thin and long, or short and fat.

  1. Pull five bars from different parts of the bundle, not just the top layer.
  2. Measure each with a tape. A 40-foot bar that measures 11.6 metres is not 40 feet.
  3. Weigh each one on a hanging scale or a shop kanta if you can borrow it. Compare against the table.
  4. Note the average, then compare with the expected figure for that bar number and length.

Mills allow a small weight tolerance per bar. I would not quote an exact figure for every grade, so ask your structural engineer what tolerance the drawings call for. As a practical rule, a consistent shortfall across your sample, rather than one odd bar, is a reason to stop unloading and escalate.

Read the bar, not just the bill

Properly rolled reinforcing bars carry raised markings on the surface. You should be able to find a mill or producer mark, the bar size and a grade mark. Grade 60 is the usual spec in Punjab, Sindh and KP structural drawings, but your own drawing decides. If the engineer's drawing says Grade 60 and the bar shows no grade marking at all, that is a conversation, not an assumption.

Also look at the ribs. Bars sold as deformed bars should have clear, regular ribs that grip concrete. Smooth, worn or uneven ribs mean weak bond, which is exactly where cracking starts in a slab.

Ask for the mill test certificate for the batch if you are building anything beyond a simple ground-plus-one house. Many small suppliers will not have one, and that is useful information too. For a big job like a three-storey 10 marla house or a plaza in Faisalabad, a certificate plus a few bars sent to a lab is cheap insurance next to what the steel bill will be.

A worked example: what a short delivery costs

Say you order 2 tonnes of #4 for the first-floor roof of a 5 marla house in Lahore. One 40-foot #4 bar should weigh about 12.1 kg, so 2,000 kg should be about 165 bars.

If the truck delivers 165 bars that each weigh 5% less than they should, you are short about 100 kg of steel while paying for 2 tonnes. At an illustrative price of PKR 250 per kg (check the day's rate, which moves with the market), that is roughly PKR 25,000 lost on one delivery. Across a whole house, with several deliveries and several bar sizes, a 5% habit can run into six figures.

The cost is not only financial. If the bars are thinner than drawn, the slab is carrying less steel than the engineer designed. That cannot be fixed after the concrete is poured.

Rust, bends and storage

Light orange surface rust is normal after a few days in humid weather and does not harm bond. Scaly, flaking rust that leaves pits is a different story. Brush a bar with a wire brush. If you can see the ribs shrinking, reject it or ask the engineer.

On site, keep bars off the ground. Two rows of bricks or a few wooden sleepers underneath will do. Muddy ground in monsoon season can rust a stack in a week. Cover the pile loosely with a tarpaulin, leaving the sides open for air, and keep bars away from cement bags and wet sand.

Check for bends too. A bar that has been straightened by hand on a hard pavement may be work-hardened or kinked. Your bar bender (mistri) can tell you quickly which bars were mishandled.

Watch the cut-and-bend stage

Many shortages happen after the truck, not before. When a mistri cuts stirrups, offcuts pile up. On a good site those offcuts get reused in short links or chairs. On a careless one, they walk out of the gate.

Ask for a bar bending schedule from your engineer or architect before work starts. It lists every bar mark, length, bend and count. Then check the tied cage against it before the shuttering closes. A quick count of stirrups per metre on a beam takes under five minutes and catches the most common cheating: wider spacing than the drawing.

Put it on paper

  • Keep every slip. Delivery challan, weighbridge slip, bill. Photograph them with the date.
  • Photograph the markings. One clear shot of each bar size's rolled marks.
  • Record the sample weights. A simple note: date, bar number, five weights, average.
  • Write the tolerance into the contract. If you are paying a contractor on a labour-and-material basis, say that steel must match the drawing's size and grade, and that you can reject deliveries that do not.

If you are still choosing between a labour-only and a full-package contractor, use the construction cost calculator to see how much of your budget steel actually represents, then decide how closely you want to control purchasing.

Make it a routine

Next time a delivery is due, send your contractor three lines the day before: the bar number, the expected count and weight for the order, and the checks you will do on arrival. Contractors behave differently when they know the owner has the table. You are not accusing anyone. You are showing that you will check, and that is usually enough to keep every delivery honest.

Steel rates change often, so confirm the day's price with at least two suppliers before ordering, and treat every figure here as a guide for checking, not a quote.

#saria#rebar#construction#grey structure#site checks

Frequently asked questions

How much does a 40-foot #4 saria bar weigh?

A #4 bar weighs roughly 1.0 kg per metre, so a 40-foot length of about 12.19 metres should weigh close to 12 kg. A #3 is about 6.8 kg, a #5 about 19 kg and a #6 about 27 kg. Confirm tolerance with your structural engineer.

How do I check a saria delivery on site?

Compare the weighbridge slip with the order, then pull five bars from different parts of the bundle. Measure their length with a tape, weigh them, and compare against expected weight for that bar number. A consistent shortfall across the sample means you should stop unloading and raise it.

Is rust on saria acceptable?

Light orange surface rust is common after humid days and does not usually harm bond. Scaly, flaking rust that leaves pits and shrinks the ribs is a problem. Brush a bar with a wire brush and ask your engineer if you are unsure. Store bars off the ground.